HELP!!! MacOS plötzlich weg nach CPU Wechsel von Ryzen 3 auf Ryzen 7. Dualboot PC (WIN11Pro + MacOS Ventura 13.3+)

  • Dr-C Probably software hasnt clone your OpenCore EFI

    you can check it also in windows

  • Das Problem scheint wohl, dass beim Klonen der Partitionen, wie üblich, der Inhalt der versteckten EFI-Partition nicht mitgeklont wurde.


    Boote ins Windows und verifiziere diese Theorie, in dem du wie folgt dort die EFI-Partition deiner neuen macOS-Platte mountest und überprüfst --> https://superuser.com/question…i-partition-on-windows-10


    Ist das tatsächlich der Fall, kannst du hierüber auch die hoffentlich noch irgendwo gesicherte, funktionierende EFI der alten macOS-Platte in die neue und leere EFI der neuen macOS-Platte kopieren.


    Danach dann im BIOS die neue macOS-Platte als Boot-Platte auswählen und weiter machen.

    Gruß
    Al6042

    Keine Unterstützung per PN oder Pinnwand... Eure Anfragen gehören ins Forum, nicht in mein Postfach!

  • Die Efi Platte ist da. Alle Inhalte drauf. Ich habe die alte Platte auch schon dran gesteckt, da wurde nichts verändert und alles ist noch drauf. Gleiches Problem. Der Bootloader taucht nicht mehr auf, auch bei der alten Platte, die normal ja unverändert ist.

    Dual Boot System:

    AMD Ryzen 7 2700X CPU - Gigabyte RX 570 GraKa - 2x 500 GB SSD Festplatte -

    2TB SATA - 10.100upm - 32 GB DDR4 - PC 3200 RAM - Fenvi T919CD WLAN & Bluetooth - Biostar Mainboard mit AMI Bios - Bluray Brenner - EVGA 450W Netzteil -

    Windows 11 Pro - MacOS Ventura 13.3.x

  • Im Bios habe ich nur die richtige Platte eingestellt. Aber da steht nur Windows Boot Manager zur Auswahl um anzubooten. Vielleicht liegt es daran. Kann auch nichts anderes auswählen.


    Kann es vielleicht am Bootmanager liegern, dass der sich nach abklemmen der Platte deaktiviert hat oder so? Kann man mit Bootice etwas machen? Ich habe leider keine Ahnung was ich noch machen soll. Die Bios Einstellungen habe ich überprüft, da ist alles unverändert.

    Dual Boot System:

    AMD Ryzen 7 2700X CPU - Gigabyte RX 570 GraKa - 2x 500 GB SSD Festplatte -

    2TB SATA - 10.100upm - 32 GB DDR4 - PC 3200 RAM - Fenvi T919CD WLAN & Bluetooth - Biostar Mainboard mit AMI Bios - Bluray Brenner - EVGA 450W Netzteil -

    Windows 11 Pro - MacOS Ventura 13.3.x

  • Does windows start?

    if so

    1) open CMD as admin

    2) diskpart

    3) list disk

    4) be sure which one is OSX disk (ie disk 2)

    5 sel disk 2

    6) sel part 1

    7)assign letter=b


    in this way you assign a letter to your EFI partition and this will mount your OSX EFI partition

    to see inside you have to use or total commander or OCAT or browse it with Task manager browse (i use this method)

    you can copy or modify things to recover any problems


    ps

    If you are confident reading this instructions you can proceed , otherwise do nothing :)

  • Efi is already there. I think it is a problem with bootloader or something. Everything is there as before. Unfortunately the old disk (cloned one) also doesn't work althought nothing was changend. Only the SATA Plug was plugged out and after plugged in it doesn't work anymore.


    No matter witch one of the disks (cloned one or Original one) you plug in, it doesn't work anymore.

    Bilder

    Dual Boot System:

    AMD Ryzen 7 2700X CPU - Gigabyte RX 570 GraKa - 2x 500 GB SSD Festplatte -

    2TB SATA - 10.100upm - 32 GB DDR4 - PC 3200 RAM - Fenvi T919CD WLAN & Bluetooth - Biostar Mainboard mit AMI Bios - Bluray Brenner - EVGA 450W Netzteil -

    Windows 11 Pro - MacOS Ventura 13.3.x

  • It is inside an EFI partition then you have an EFI folder

    then another EFI folder with BOOT and OC

    it is wrong in this way

    and it seems you mixed also with stuff useful to boot windows

  • what should i delete or change?

    Dual Boot System:

    AMD Ryzen 7 2700X CPU - Gigabyte RX 570 GraKa - 2x 500 GB SSD Festplatte -

    2TB SATA - 10.100upm - 32 GB DDR4 - PC 3200 RAM - Fenvi T919CD WLAN & Bluetooth - Biostar Mainboard mit AMI Bios - Bluray Brenner - EVGA 450W Netzteil -

    Windows 11 Pro - MacOS Ventura 13.3.x

  • i think it is better if a user explain better in german language

    i try but verify well my instruction


    Have you windows and OSX on a single disk in two partition?


    however this below is the EFi of windows (i have on two separate disk (windows and OSX))


    this below is my OSX EFI partition:


    i boot windows starting with this efi and using opencore as boot loader

    from here i can boot Windows or OSX


    What was your previous working config?

    From opencore you could boot OSX or Windows?


    Separate disk for Windows or OSX?


    this is your situation:


    OC andBoot folders should be at the same level of _MACOSX folder i see in your picture

    Not inside another EFI folder

  • Es macht den Anschein als hättest du den EFI-Ordner in der EFI-Partition deiner Windows-Platte kopiert.

    Wenn macOS auf einer anderen Festplatte installiert ist, muss der EFI-Ordner auch in die dortige EFI-Partition.
    Erst dann wird dir die macOS-Platte auch als bootfähig im BIOS angezeigt werden.

    Gruß
    Al6042

    Keine Unterstützung per PN oder Pinnwand... Eure Anfragen gehören ins Forum, nicht in mein Postfach!

  • Verstehe nur nicht, dass auch die Ursprungsplatte (die geclont) und an der nichts verändert wurde auch nicht mehr den Opencore Bootloader lädt und direkt ins Windows bootet. Es wurde nur der Sata Stecker abgezogen und an die neue angeklemmt. Aber nun funktioniert halt auch die alte Platte nicht mehr. Das muss doch bestimmt am Bios oder so liegen. 🤷🏻‍♂️

    Dual Boot System:

    AMD Ryzen 7 2700X CPU - Gigabyte RX 570 GraKa - 2x 500 GB SSD Festplatte -

    2TB SATA - 10.100upm - 32 GB DDR4 - PC 3200 RAM - Fenvi T919CD WLAN & Bluetooth - Biostar Mainboard mit AMI Bios - Bluray Brenner - EVGA 450W Netzteil -

    Windows 11 Pro - MacOS Ventura 13.3.x

  • oder du hast einfach unwissentlich die oc-config geschrottet- das passiert auch schon mal :)

    - das "bios" guckt zuerst in die bootorder, bzw. festgelegte boot platte, dort in deinem fall in die fat32 partition und folgend in den ordner "efi"- wenn damit irgendetwas wie z.b. die prüfsumme nicht stimmt,- geht das eben nicht weiter- /die verschachtelung ist verkehrt -passiert, daher ggf. immer nen usb-stick mit der gesicherten efi in petto haben.


    lg :)

  • EFI structure posted above is wrong for OSX (a nested EFI in other EFi folder)

    Opencore can't boot in this way

  • Efi is now right? And I've done diskpart, list disk and something posted before with letter=B, now there is a second drive with an efi.

  • Now the Efi structure is fine

    I can’t say if inside boot and oc folders there are the right files

  • In the program "Bootice" there is Windows Boot Manager and CD/DVD Driver. There is no entry for MacOS or something other. I think it is a problem with Bootmanager, Bios or Opencore. What can I do, that Opencore is listed before he boots into windows?

    Dual Boot System:

    AMD Ryzen 7 2700X CPU - Gigabyte RX 570 GraKa - 2x 500 GB SSD Festplatte -

    2TB SATA - 10.100upm - 32 GB DDR4 - PC 3200 RAM - Fenvi T919CD WLAN & Bluetooth - Biostar Mainboard mit AMI Bios - Bluray Brenner - EVGA 450W Netzteil -

    Windows 11 Pro - MacOS Ventura 13.3.x

  • I wouldn’t touch nothing with bootice

    I would try to choose disk from bios to boot if you have adjusted Efi partition as I see in last your pictures

  • There is only Windows Boot Manager in Bios available. I remember in June this Year, we have installed an I7 CPU. There was the same problem, you solved it. At this time it was an entry "Opencore" in Bios. This entry is not shown, now.

    Dual Boot System:

    AMD Ryzen 7 2700X CPU - Gigabyte RX 570 GraKa - 2x 500 GB SSD Festplatte -

    2TB SATA - 10.100upm - 32 GB DDR4 - PC 3200 RAM - Fenvi T919CD WLAN & Bluetooth - Biostar Mainboard mit AMI Bios - Bluray Brenner - EVGA 450W Netzteil -

    Windows 11 Pro - MacOS Ventura 13.3.x

  • If you can post boot and oc folder in a zip file to see if they are fine