Suchergebnisse
Suchergebnisse 1-20 von insgesamt 105.
-
@derHackfan Je pense que tu veux dire:... dans notre forum!ou:... en ce forum! C'est un peux plus précisé
-
Was ist der unterschied? @UserD
-
Denk dran, falls es funzt deine Signatur abzupassen @UserD
-
Hat sich da jetzt was getan was ich verpasst habe? Ich dachte immer ozmosis geht bis aller höchstens z97 ... Oder hab ich da jetzt was verpasst?
-
Rev steht für Revision. Also Revision 1 ist halt das erste auf den Markt gebrachte mit dieser Bezeichnung. Manchmal bringen die Firmen danach noch ein 2. oder 3. board raus. Steht meistens auf dem board selber
-
Haha @griven you linked the b85m-ds3h but he has a b85m-d3h. I'll search for the correct link at my PC @fhf1231Well, im sorry, but there is no Rom based in f15. Herr you can find all the Roms:Mod für GA-B85M-D3HThe last one is the f14 167x-Mass. But it is NOT sierra ready
-
Nix da, sorry ozmosis lässt sich noch nicht in 100series Boards einfügen. Genauso wenig wie in X99, tut mir leid @allegro
-
Jo, aber ich kanns leider nicht ändern Aber was spricht gegen Clover?
-
I fear it is not possible to insert Ozmosis into that Rom, I am Sorry! There isn't enough space You probably need to load Ozmosis from the EFI partition or use Clover!
-
Hier der Link: Mod fürs Z97 MPOWERWenn du mir noch sagst welchen Audio Codec das Teil hat, mach ich dir auch noch fix eine DSDT fertig @Zhaman
-
Das hab ich gemacht aber da hat meine suche nichts mit audio codec gefunden. Okay, wenn mir @al6042 nicht zuvor kommt, dann Kriegst du die dsdt halt heute mittag
-
Tja... Ich bekomme wenn ich den Eintrag (replace TMR to TIMR irgendwie sowas) nicht aus den Basic Apple Device Renames rausnehme einen Syntax Fehler ... expecting ')'. rausgenommen - nächster Fehler: Name already exists in scope. Ich hab gelesen, dass dann irgendwas davon schon wo anders existiert, aber leider find ich das nicht Ich weiß auch gar nicht was ich suchen muss... Ich glaube ich brauche noch etwas Nachhilfe bei dir!
-
Pass acht Ich hab jetzt die Basic Apple Device Renames rein gehauen, nach "TIMR" gesucht und alle mit "TMR" wieder ersetzt. Damit ist der Fehler auch wieder weg. Dann hab ich die DTGP Methode eingebaut. Dann den ALC1150 Patch aus einem Z97X-UD5H genommen und dort eingefügt. Dann bekomme ich diesen Fehler (Fehlerzeile auf dem Bild zu sehen):Wenn ich dann den ganzen Scope da raus nehme, gehts, aber ich weiß nicht ob das dann die DSDT beschädigt und Ton nachher nicht mehr geht. Nicht umsonst steht …
-
Achso dann hatte ich es schon OK ich lad sie eben hoch, danke dir EDIT: Okay, klasse! DSDT ist hochgeladen und nun neben dem Bios zu finden. Danke für deine Hilfe @al6042 !
-
Bittesehr Jaja Forensoftware, mecker nicht. Hier hast du deine 3 Wörter...
-
Sorry, could you try to speak English? I think it would be easier to understand, because your sentence does not really make sense English might not be a problem for us here
-
So you flashed the BIOS i created and installed MacOS Sierra succesfully?Well, but if you changed some things in the defaults.plist i extracted Form the BIOS i gave you... Where did you put it, so that it has an influence on the system and its booting process? As i know, it can only be loaded from the BIOS or the hidden efi partition. So i think you did not insert it into the BIOS. But if you did not put it to your efi partition, it is not loaded at all. So the defaults.plist can't be your Probl…
-
No!!! Did you change the Whole file with the Name OzmosisDefaults? You may only change the raw section in it! Please flash the BIOS i gave you again and load the defaults.plist Form the efi partition. I am sure your macOS has one as well!
-
Please type the following in terminal:diskutil listThen you might See a list of all partitions on your Boot drive. There will be a partition called "diskXs1" but instead of X it will be a number. Normaly this is 1. These Xs1 partitions are always the EFI partitions. So you type:diskutil mount diskXs1But again instead of X you type the correct idetifier of your efi partition. Then you will See it, believe me
-
So do you now use the DSDT file?? Does Sound work?do you use VGA? If not, you can try pressing ALT and press on "scaled" in Preferences - Monitor. Then you should be able to change the Resolution. If not, try the program SwitchResX